Product Description
Brand New Kenwood KAC-8105D Class D Mono 1000 Watt Class D Amplifier Features: Kenwood KAC-8105D Class D 1000 Watts amplifier CEA-Compliant Amplifier 300 watts x 1 at 4ohms 500 watts x 1 at 2 ohms 1000 watts x 1 Max Power Output Built-In Low Pass Crossover Filter (50-200 HZ @ 24 dB per octave) Subsonic Filter Short circuit, DC offset, overload, and thermal protection circuitry Variable Bass Boost LED Power-On Indicator Built In Cooling Fan MOSFET Power Supply Speaker Level Input Signal Sensing Auto Turn-On Input Sensitivity: 0.2 - 5 volts Frequency response: 10-200 Hz Aluminum die cast heat sink Gold-plated RCA level inputs Gold-plated screw terminals Preamp RCA output 4 Gauge Power and Ground Inputs Dimensions: 11"L x 2-5/16"H x 9-3/8"D
| Price: | $109.99 |
| as of Fri, 22 Feb 2013 07:48:03 GMT ***Remember, deals price on this item for sale just for limited time*** | |
Product Details
- Amazon Sales Rank: #24755 in Car Audio or Theater
- Brand: Kenwood
Features
- Kenwood KAC-8105D Class D 1000 Watts amplifier
- 300 watts x 1 at 4ohms
- 500 watts x 1 at 2 ohms
- Short circuit, DC offset, overload, and thermal protection circuitry
- Dimensions: 11"L x 2-5/16"H x 9-3/8"D
Customer Reviews
Most helpful customer reviews
2 of 2 people found the following review helpful.
By M. D. Burns
This amp works well. We installed it with a pair of 12" subs, added a capacitor, and it does what it is advertised to do. It hits hard, sounds good and hopefully will prove to be reliable. We've only had it installed for two weeks now. It wasn't to difficult to install and wire up. If you are viewing the picture on this Amazon site, the two mounting holes that you can see are a little difficult to work with if you are mounting in a tight place. They are recessed so deep that you can't get your fingers in there to get your screw through the hole and start them in to your mounting surface. The only other problem I had was when I installed the capacitor, I had to put two power wires on the lug to the amp, which is not designed for that. It was a little difficult to get the screw to tighten up. If by chance you strip out the screw, the hole goes all the way through, so you can get your own small bolt, nut and washers, and replace the screw with that. You can actually tighten it better that way. Once I get it all mounted and wired, it fired right up and with a few adjustments to the low pass filter and input sensitivity, it was thumping! We noticed it does run pretty warm so we're considering putting a fan on it because the trunk has limited air flow. If you are looking for a good mono amp to drive a set of subs, this is a good buy.
1 of 1 people found the following review helpful.
By AUDIO ENTHUSIAST
I have had this Amp for almost 2 years now and it hits hard. I have it hooked up to 2 kicker competition 12s and they are very evenly matched. No capacitor and my lights do not dim and it runs cool. I have them wired at 2ohms in parallel and giving them 500w rms. This amp is amazing for its price and has been extremely reliable. I have read reviews about it not working after a few weeks and noticed that the common factor in these reviews is that they had it installed at a "professional" car stereo shop. I think the problem was with the person or rather shop that installed than the amp. I have been using Kenwood Amps since the early 90s and they have never made any unreliable amps in my opinion. I WOULD DEFINITELY RECOMMEND!!! ESPECIALLY AT THIS PRICE POINT. DO YOURSELF A FAVOR, BUY IT!!
0 of 0 people found the following review helpful.
By Jeff
Good amp, pushes the power it states.. Have it running a pair of Kenwood 12 shallows and it's a good combination. Honest 500+ watts at 2 ohms and doesn't overheat/shut down. NOTE THIS UNIT DOES NOT HAVE FANS as some sites report that it does.
No comments:
Post a Comment